4G Lora IoT DN15 to DN25 Water Meter with Valve Control

• Customization: Available
• Usage: Irrigation
• Type: Irrigation System
• Model NO.: QT-01F-N/L/G
• Drainage & Irrigation Mode: Sprinkler Irrigation Equipment
• Pump Type: Centrifugal Pump
• Ground Drainage and Irrigation Machinery Type: Siphon Irrigation
• Certification: CCC, CE
• Condition: New
• Application Field: Agriculture
• Pressure: 1.6MPa
• Flow Meter: Built-in Meter
• Communication Protocol 1: 4G
• Communication Protocol 2: Lora
• Pipe Size: DN25mm
• Transport Package: Gift Box
• Specification: 17.3*7.9*19.9cm
• Trademark: QOTO
• Origin: China
• HS Code: 8501310000
• Production Capacity: 100000PCS/Year
• Package Size: 15.00cm * 13.00cm * 10.00cm
• Package Gross Weight: 1.500kg

Product Description

Product introduction
As much as 50% of this water is wasted due to overwatering caused by inefficiencies in traditional irrigation methods and systems. Smart irrigation technology is the answer.

QOTO IoT Smart irrigation systems tailor watering schedules and run times automatically to meet specific landscape needs. These controllers significantly improve outdoor water use efficiencies.

Unlike traditional irrigation controllers that operate on a preset programmed schedule and timers, smart irrigation controllers monitor weather, soil conditions, evaporation and plant water use to automatically adjust the watering schedule to actual conditions of the site.
 

The electric valve base remote irrigation system can be applied in residential, commercial, agricultural irrigation. Using 4G GSM remote control or Lora local internet makes irrigation a more science and intelligent program to save more water and labor.

 

1,remote control by Mobile phone or PC computer

2,irrigation water capacity setting, to control water consumption

3,Wireless installation: powered by solar panel+18650 batteries
4. As a Lora actuator supplier, we develop and manufacture the actuator by our own technology, we can provide free API for further intergration.

Model	specification		configuration
QT-01F-N/L/G	Power supply	DC 5V 2A(solar panel+18650 battery 1pcs or 2pcs)	smart valve controller+1 inch valve*1
	communication protocol	Lora/NB-iot/4G
	protection level	IP67
	Working Temp	-20~75ºC	Flow Meter--DN25
	Media Temp	0~70ºC
	valve caliber	DN25

What other products DIY sprinkler irrigation system need

SPRINKLER SYSTEM PLANNING

Plot, Plan, and Design

1. The first step in designing a residential system is to  measure the property and indicate the location of  the house. On a separate piece of paper, sketch out your property and place your measurements on the sketch. Be sure to include all concrete or brick walks and patios, driveways, and fences. While you are measuring, locate any trees, shrubs, and lawns and draw them on the sketch.

Draw Sprinkler Head Locations

Decide where you will be installing large area sprinklers and where you will be installing small area sprinklers. Large area sprinklers

should be 25' to 40' apart. Small area sprinklers should be 8' to 17' apart. This spacing will allow spray patterns to overlap and

assure even water distribution. Do not mix sprinkler types within one area. Do not place sprinkler heads too far apart; stay

within specifications listed on the Sprinkler Performance Charts, which can be found in the Hunter Product Catalog. Spacing is

determined by the size of the area the sprinkler is serving. Additionally, a sprinkler should be spaced so that it will spray both the

head next to it and the head across from it. Working with one area at a time, start placing sprinkler heads:

                         

Step 1

The critical points on a plan

are the corners. Draw a

quarter pattern sprinkler

in each corner. Using a

compass, draw an arc

showing the sprinkler's

watering pattern.   

             

Step 2

If the quarter heads will not

spray each other (head-to-

head spacing), place heads

along the perimeters. Draw

these sprinklers' watering

patterns.

Step 3

Now look to see if the perimeter heads will be spraying

across the area to the heads on the other side. If they do

not, add full circle heads in the middle. An easy way to locate

these heads is to draw perpendicular grid lines from one

perimeter head to another. Again, using the compass, draw

an arc showing this sprinkler's watering pattern to make sure

there is complete coverage.

Curved Areas

Convert curved areas to a series of straight lines; place

sprinklers the same as you would in square or rectangular

areas. Adjustable arc nozzles on spray heads work very well

in curved areas.